PERMABOND 200

Harmonization Code : 3506.10.00.00 | Prepared glues and other prepared adhesives, not elsewhere specified or included; products suitable for use as glues or adhesives, put up for retail sale as glues or adhesives, not exceeding a net weight of 1 kg

PERMABOND 200

Main features

  • 1,500 mPa s Application Viscosity
  • 15-Second Fixturing Time
  • 22 N/mm^2 Shear Strength

Product Description

PERMABOND® 200 Cyanoacrylate Adhesive is a high-viscosity, single-component ethyl cyanoacrylate adhesive developed for wire-tacking and general component-bonding applications. Its 1,500 mPa·s viscosity supports controlled placement and helps bridge gaps up to 0.38 mm. The adhesive is suitable for plastics, rubber, and metals and reaches typical handling strength in approximately 15 seconds on steel, Buna N rubber, and phenolic. Full strength develops in 24 hours. The solvent-free, 100% reactive formulation requires no mixing or heat cure and is suited to rapid industrial assembly.

Key features

  • High-viscosity formulation: A viscosity of 1,500 mPa·s supports controlled application, wire tacking, and gap filling up to 0.38 mm.
  • Fast fixture performance: Reaches typical handling strength in approximately 15 seconds on steel, Buna N rubber, and phenolic.
  • Simple one-part processing: Requires no mixing or heat cure and contains no solvent.

Applications / Suitable for

  • Wire-tacking applications
  • Bonding components with small gaps
  • High-speed industrial assembly
  • Bonding plastics, rubber, and metals
Product Family

PERMABOND 200

Loading pricing…
TDS, SDS & Technical Documents

Technical Specifications

General Properties
Appearance
Appearance at room temperature.
Liquid
Chemistry Type
Ethyl cyanoacrylate
Color
The color
Colourless
Specific Gravity
Specific gravity (SG) is the ratio of the density of a substance to the density of a reference substance; equivalently, it is the ratio of the mass of a substance to the mass of a reference substance for the same given volume. For liquids, the reference substance is almost always water (1), while for gases, it is air (1.18) at room temperature. Specific gravity is unitless.
1.05
Physical Properties
Viscosity
Viscosity is a measurement of a fluid’s resistance to flow. Viscosity is commonly measured in centiPoise (cP). One cP is defined as the viscosity of water and all other viscosities are derived from this base. MPa is another common unit with a 1:1 conversion to cP. A product like honey would have a much higher viscosity -around 10,000 cPs- compared to water. As a result, honey would flow much slower out of a tipped glass than water would. The viscosity of a material can be decreased with an increase in temperature in order to better suit an application
1,500 mPa.s
Mechanical Properties
Impact Strength
3-7 kJ/m² mm
Electrical Properties
Dielectric Strength
Dielectric strength is measured in kV per mm and is calculated by the Breakdown voltage divided by the thickness of the tested material. Those two properties go hand in hand and while Breakdown voltage is always thickness dependent, dielectric strength is a general material property. As an example, the dielectric strength of Polyimide is 236 kV/mm. If we place 1mm of Polyimide between two electrodes, it will act as an insulator until the voltage between the electrodes reaches 236 kV. At this point it will start acting as a good conductor, causing sparks, potential punctures and current flow.
10 kV/mm
Maximum gap fill
038 mm

Additional Information

Technical properties

As-supplied / before-processing properties

Typical uncured and curing properties. Values are guideline information and do not constitute product specifications.

Property Value Unit Method / condition
Chemical composition Ethyl cyanoacrylate — Single-component adhesive
Appearance Colorless liquid — As supplied
Viscosity 1,500 mPa·s At 25 °C; equivalent to cP
Specific gravity 1.05 — Typical uncured value
Maximum gap fill 0.38 mm Equivalent source value 0.015 in
Fixture time — steel 15 s Time to 0.3 N/mm² shear strength
Fixture time — Buna N rubber 15 s Time to 0.3 N/mm² shear strength
Fixture time — phenolic 15 s Time to 0.3 N/mm² shear strength
Full strength 24 h Typical full-strength development
Technical properties

After-processing / final-state properties

Typical cured performance values. Bond strength varies with substrate, surface preparation, joint gap, and curing conditions.

Property Value Unit Method / condition
Shear strength — steel 22 N/mm² ISO 4587; equivalent source value 3,200 psi
Shear strength — aluminum 8 N/mm² ISO 4587; equivalent source value 1,200 psi
Impact strength 3–7 kJ/m² ASTM D950
Hardness 85 Shore D ISO 868
Dielectric strength 250 V/mil Typical cured electrical property
Minimum exposure temperature -55 °C Depends on the bonded materials; equivalent source value -65 °F

Leading Brands Trust in Our Products and Services

Products that Perform| Knowledge that Serves| Service that Delivers