DEVCON 10760

Harmonization Code : 3506.91.90.99 | Prepared glues and other prepared adhesives, not elsewhere specified or included; products suitable for use as glues or adhesives, put up for retail sale as glues or adhesives, not exceeding a net weight of 1 kg ; Adhesives based on polymers of headings 3901 to 3913 or on rubber; Other ; Other

DEVCON 10760

Main features

  • Titanium-Reinforced Epoxy Putty
  • Non-Sag Placement Control
  • Machinery Repair Applications

Product Description

DEVCON® Titanium Putty (10760) is a two-component, titanium-reinforced epoxy repair putty for rebuilding and restoring worn machinery and precision metal parts. The grey, non-sag material can be applied in sections up to 1/2 inch thick on vertical surfaces and cures to a machinable finish that can be drilled, tapped, painted, or machined. Typical cured performance includes 15,200 psi (105 MPa) compressive strength, 2,000 psi (14 MPa) adhesive tensile shear strength, and dry temperature resistance to 350°F (177°C). It is supplied as a premeasured resin-and-hardener system with a 21-minute pot life at 72°F (23°C).

Key features

  • Titanium-reinforced repair putty: Restores worn or damaged metal parts requiring a durable, machinable finish.
  • High compressive strength: Develops a typical compressive strength of 15,200 psi (105 MPa) after curing for 7 days at 75°F (24°C).
  • Non-sag application: Can be troweled onto vertical surfaces at thicknesses up to 1/2 inch without sagging.

Applications / Suitable for

  • Restoring bearing housings and scored shafts
  • Rebuilding wear rings, hydraulic rams, and valves
  • Repairing machinery and precision parts requiring a machined finish
Product Family

DEVCON 10760

Loading pricing…

Technical Specifications

Thermal Properties
Temperature Resistance
Temperature resistance is the maximum temperature that the material or product can withstand for a period of time. The temperatures listed should be considered as guidelines for an operating temperature of about 30 minutes. Typically, the material can withstand much longer times at temperatures about 20°C lower and can withstand much higher temperatures for short, intermittent times.
177 ˚C
Electrical Properties
Dielectric Strength
Dielectric strength is measured in kV per mm and is calculated by the Breakdown voltage divided by the thickness of the tested material. Those two properties go hand in hand and while Breakdown voltage is always thickness dependent, dielectric strength is a general material property. As an example, the dielectric strength of Polyimide is 236 kV/mm. If we place 1mm of Polyimide between two electrodes, it will act as an insulator until the voltage between the electrodes reaches 236 kV. At this point it will start acting as a good conductor, causing sparks, potential punctures and current flow.
2.2 kV/mm
Mechanical Properties
Molded Shrinkage
0.0010 %
General Properties
Color
The color
gray
Mix Ratio
The amount of a constituent divided by the total amount of all other constituents in a mixture
3:1:1
Pot Life
Pot life is the amount of time it takes for the viscosity of a material to double (or quadruple for lower viscosity materials) in room temperature after a material is mixed. It is closely related to work life but it is not application dependent, less precise and more of a general indication of how fast a system is going to cure.
21 minutes
Solids
100 %
Specific Gravity
Specific gravity (SG) is the ratio of the density of a substance to the density of a reference substance; equivalently, it is the ratio of the mass of a substance to the mass of a reference substance for the same given volume. For liquids, the reference substance is almost always water (1), while for gases, it is air (1.18) at room temperature. Specific gravity is unitless.
2.36

Additional Information

Technical properties

As-supplied / before-processing properties

Typical uncured and processing properties at 72°F (23°C), unless otherwise stated. Values are representative and are not intended for specification purposes.

Property Value Unit Method / condition
Product form Two-component putty — Resin and hardener
Color Grey — Mixed material
Mix ratio by volume 3.1:1 — Resin:hardener
Mix ratio by weight 4.3:1 — Resin:hardener
Mixed viscosity Putty — At 72°F (23°C)
Specific gravity 2.36 g/cm³ Equivalent to 19.7 lb/gal
Pot life 21 minutes At 72°F (23°C)
Functional cure 16 hours At 72°F (23°C); cure time varies with application temperature
Technical properties

After-processing / final-state properties

Typical cured properties measured after 7 days at 75°F (24°C), unless otherwise stated. Values are representative and are not intended for specification purposes.

Property Value Unit Method / condition
Adhesive tensile shear 2,000 (14) psi (MPa) ASTM D1002; cured 7 days at 75°F (24°C)
Compressive strength 15,200 (105) psi (MPa) ASTM D695; cured 7 days at 75°F (24°C)
Flexural strength 7,700 (53) psi (MPa) ASTM D790; cured 7 days at 75°F (24°C)
Hardness 87 Shore D ASTM D2240; cured 7 days at 75°F (24°C)
Modulus of elasticity 9.5 × 105 (6.6) psi (GPa) ASTM D638; cured 7 days at 75°F (24°C)
Cured shrinkage 0.0010 in/in (cm/cm) ASTM D2566; cured 7 days at 75°F (24°C)
Dielectric strength 56 (2.2) V/mil (kV/mm) ASTM D149; cured 7 days at 75°F (24°C)
Temperature resistance Wet: 150 (65); dry: 350 (177) °F (°C) Documented wet and dry temperature-resistance limits

Leading Brands Trust in Our Products and Services

Products that Perform| Knowledge that Serves| Service that Delivers